1-Wire Protocol
Learn about the communication between devices or sensors using the OneWire protocol.
This article was revised on 2022/09/28 by Hannes Siebeneicher.
Controller/peripheral is formerly known as master/slave. Arduino no longer supports the use of this terminology. Devices formerly known as master are referred to as controller and devices formerly known as slaves are referred to as peripheral.
1-Wire communication is a protocol operating through one wire between the controller device and the peripheral device. This article covers the basics of using the 1-Wire protocol with an Arduino with the help of the OneWire library. The following sections provide information about the 1-Wire protocol, interface, power, addressing devices, reading devices and finally a short glimpse into the library's history.
Latest version
The latest version of the library is on Paul Stoffregen's site.
OneWire is currently maintained by Paul Stoffregen. If you find a bug or have an improvement (to the library), email paul@pjrc.com. Please be sure you are using the latest version of OneWire.
Bus is a subclass of the OneWire library. Bus class scans the 1-Wire Bus connected to an analog pin and stores the ROMs in an array. Several methods are available in the Bus class to acquire data from different 1-Wire sensors (DS18B20, DS2438).
The 1-Wire Protocol
Dallas Semiconductor (now Maxim) produces a family of devices that are controlled through a proprietary 1-Wire protocol. There are no fees for programmers using the Dallas 1-Wire (trademark) drivers.
On a 1-Wire network, which Dallas has dubbed a "MicroLan" (trademark), a single controller device communicates with one or more 1-Wire peripheral devices over a single data line, which can also be used to provide power to the peripheral devices. (Devices drawing power from the 1-wire bus are said to be operating in parasitic power mode.) Tom Boyd's guide to 1-Wire may tell you more than you want to know, but it may also answer questions and inspire interest.
The 1-Wire temperature sensors have become particularly popular, because they're inexpensive and easy to use, providing calibrated digital temperature readings directly. They are more tolerant of long wires between sensor and Arduino. The sample code below demonstrates how to interface with a 1-Wire device using Jim Studt's OneWire Arduino library, with the DS18S20 digital thermometer as an example. Many 1-Wire chips can operate in both parasitic and normal power modes.
1-Wire Interfaces
Dedicated Bus Controller
Dallas/Maxim and a number of other companies manufacture dedicated bus controller for read/write and management of 1-Wire networks. Most of these are listed here:
http://owfs.org/index.php?page=bus-masters
These devices are specifically designed and optimized to read and write efficiently to 1-Wire devices and networks. Similar to UART/USART controller, they handle clocked operations natively with the use of a buffer, offloading the processing load from the host processor (e.g., sensor gateway or microcontroller) thereby increasing accuracy . External pull-up resistors are also often not required.
Many of the chips provide error-handling that specifically deals with loss of signal integrity, level variation, reflections, and other bus issues that may cause problems, particularly on large networks. Many of the devices have additional features, and are offered on a large variety of interfaces. They range in price from $1 to $30.
Another key advantage is support of , a read/write file system with vast device support for 1-Wire controller that exposes many native functions for a wide variety of 1-Wire device types.
UART/USART controller
Most UART/USARTs are perfectly capable of sustained speeds well in excess of the 15.4kbps required of the 1-Wire bus in standard mode. More important, the clock and buffering is handled separately, again offloading it from the main process of the microcontroller or main processor. This implementation is discussed here: http://www.maximintegrated.com/en/app-notes/index.mvp/id/214.
Bitbanging approaches
Where native buffering/clock management is not available, 1-Wire may be implemented on a general purpose IO (GPIO) pin, where manual toggle of the pin state is used to emulate a UART/USART with reconstruction of the signal from the received data. These are typically much less processor-efficient, and directly impact and are directly impacted by other processes on the processor shared with other system processes.
On Arduino and other compatible chips, this may be done with the OneWire library.
On single-board computers such as the Raspberry Pi, 1-Wire network read is often possible using kernel drivers that offer native support. The w1-gpio, w1-gpio-therm, and w1-gpio-custom kernel mods are included in the most recent distributions of Raspbian and are quite popular, as they allow interfacing with a subset of 1-Wire device with no additional hardware. Currently, however, they have limited device support, and have bus size limitations in software.
Powering OneWire devices
The chip can be powered two ways. One way is the "parasitic" option,meaning that only two wires need go to the chip. The other may, in some cases, give a more reliable operation (parasitic often works well), as an extra wire carrying the power for the chip is involved. For getting started, especially if your chip is within 20 feet of your Arduino, the parasitic option is probably fine. The code below works for either option.
Parasite power mode
When operating in parasite power mode, only two wires are required: one data wire, and one ground. In this mode, the power line must be connected to ground, per the datasheet. At the controller, a 4.7k pull-up resistor must be connected to the 1-wire bus. When the line is in a "high" state, the device pulls current to charge an internal capacitor.
This current is usually very small, but may go as high as 1.5 mA when doing a temperature conversion or writing EEPROM. When a peripheral device is performing one of these operations, the bus controller must keep the bus pulled high to provide power until the operation is complete; a delay of 750ms is required for a DS18S20 temperature conversion. The controller can't do anything during this time, like issuing commands to other devices, or polling for the peripheral's operation to be completed. To support this, the OneWire library makes it possible to have the bus held high after the data is written.
Normal (external supply) mode
With an external supply, three wires are required: the bus wire, ground, and power. The 4.7k pull-up resistor is still required on the bus wire. As the bus is free for data transfer, the microcontroller can continually poll the state of a device doing a conversion. This way, a conversion request can finish as soon as the device reports being done, as opposed to having to wait for conversion time (dependent on device function and resolution) in "parasite" power mode.
Note on resistors:
For larger networks, you can try smaller resistors.
The ATmega328/168 datasheet indicates starting at 1k6 and a number of users have found smaller to work better on larger networks.
Addressing a 1-Wire device
Each 1-Wire device contains a unique 64-bit 'ROM' address, consisting of an 8-bit family code, a 48-bit serial number, and an 8-bit CRC. The CRC is used to verify the integrity of the data. For example, the sample code, below, checks if the device being addressed is a DS18S20 temperature sensor by checking for its family code, 0x10. To use the sample code with the newer DS18B20 sensor, you would check for a family code of 0x28, instead, and for the DS1822 you would check for 0x22.
Single-device commands
Before sending a command to a single peripheral device, the controller must first select that device using its unique ROM. Subsequent commands will be responded to by the selected device, if found.
Multiple-device commands
Alternatively, you can address a command to all peripheral devices by issuing a 'Skip ROM' command (0xCC), instead. It is important to consider the effects of issuing a command to multiple devices. Sometimes, this may be intended and beneficial. For example, issuing a Skip ROM followed by a convert T (0x44) would instruct all networked devices that have a Convert T command to perform a temperature conversion. This can be a time-saving and efficient way of performing the operations. On the other hand, issuing a Read Scratchpad (0xBE) command would cause all devices to report Scratchpad data simultaneously. Power consumption of all devices (for example, during a temperature conversion) is also important when using a Skip ROM command sequence.
Reading a 1-Wire device
Reading a 1-Wire device requires multiple steps. The details are device-dependent, in that devices are capable of reporting different measurables. The popular DS18B20, for example, reads and reports temperature, while a DS2438 reads voltage, current, and temperature.
Two Main Read Process Steps:
Conversion
A command is issued to the device to perform an internal conversion operation. With a DS18B20, this is the Convert T (0x44) byte command. In the OneWire library, this is issued as ds.write(0x44), where ds is an instance of the OneWire class. After this command is issued, the device reads the internal ADC, and when this process is complete, it copies the data into the Scratchpad registers. The length of this conversion process varies depending on the resolution and is listed in the device datasheet. a DS18B20 takes from 94 (9-bit resolution) to 750ms (12-bit resolution) to convert temperature. While the conversion is taking place, the device may be polled, e.g. using in the ds.read() command in OneWire, to see if it has successfully performed a conversion.
Read Scratchpad
Once the data has been converted, it is copied into the Scratchpad memory, where it may be read. Note that the Scratchpad may be read at any time without a conversion command to recall the most previous reading, as well as the resolution of the device and other device-dependent configuration options.
Asynchronous vs. Synchronous read/write
The majority of existing code for 1-Wire devices, particularly that written for Arduino, uses a very basic "Convert, Wait, Read" algorithm, even for multiple devices. This creates several problems:
Program timing for other functions
Arguably the biggest problem with using the above methodology is that unless threading measures are undertaken, the device must sit (hang) and wait for the conversion to take place if a hardcoded wait time is included. This presents a serious problem if other timed processes exist, and even if they don't -- many programs wait for user input, process data, and perform many other functions that cannot be put on hold for the time necessary for a temperature conversion process. As noted, a 12-bit conversion process for a DS18B20 can take as long as 750ms. There is no reason to use the wait method, unless it is desired that the controller does nothing (at all) until the measurement conversion is complete. It is far more efficient to issue a conversion command and return later to pick up the measurement with a Read Scratchpad command once the conversion is complete.
Scaling for Poll Speed with multiple devices
Another major problem with the "Convert, Wait, Read" method is that it scales very poorly, and for no good reason. All conversion commands can be issued in series (or simultaneously) by issuing a Skip ROM and then converting the command so the result can then be read back in succession. See discussion here: http://interfaceinnovations.org/onewireoptimization.html.
Adjustment of wait time to required conversion time
The most efficient and expeditious read of 1-Wire devices explicitly takes the conversion time of the device being read into account, which is typically a function of read resolution. In the example below, for example, 1000ms is given, while the datasheet lists 750ms as the maximum conversion time, and typical conversion takes place in 625ms or less. Most important, the value should be adjusted for the resolution that is currently being polled. A 9-bit conversion, for example, will take 94ms or less, and waiting for 1000ms simply does not make sense. As noted above, the most efficient way to poll is the use a read time slot to poll the device. This way one can know exactly when the result is ready and pick it up immediately.
History
In 2007, Jim Studt created the original OneWire library that makes it easy to work with 1-Wire devices. Jim's original version only worked with arduino-007 and required a large (256-byte) lookup table to perform CRC calculations. This was later updated to work with arduino-0008 and later releases. The most recent version eliminates the CRC lookup table and has been tested under arduino-0010.
The OneWire library had a bug causing an infinite loop when using the search function but Version 2.0 merges Robin James's improved search function and includes Paul Stoffregen's improved I/O routines (fixes occasional communication errors), and also has several small optimizations.
Version 2.1 added compatibility with Arduino 1.0-beta and an improved temperature example (Paul Stoffregen), DS250x PROM example (Guillermo Lovato), chipKit compatibility (Jason Dangel), CRC16, convenience functions and DS2408 example (Glenn Trewitt).
Miles Burton derived its Dallas Temperature Control Library from it as well.
Example code
1#include <OneWire.h>2
3
4// DS18S20 Temperature chip i/o5
6OneWire ds(10); // on pin 107
8
9void setup(void) {10
11 // initialize inputs/outputs12
13 // start serial port14
15 Serial.begin(9600);16
17}18
19
20void loop(void) {21
22 byte i;23
24 byte present = 0;25
26 byte data[12];27
28 byte addr[8];29
30
31 ds.reset_search();32
33 if ( !ds.search(addr)) {34
35 Serial.print("No more addresses.\n");36
37 ds.reset_search();38
39 return;40
41 }42
43
44 Serial.print("R=");45
46 for( i = 0; i < 8; i++) {47
48 Serial.print(addr[i], HEX);49
50 Serial.print(" ");51
52 }53
54
55 if ( OneWire::crc8( addr, 7) != addr[7]) {56
57 Serial.print("CRC is not valid!\n");58
59 return;60
61 }62
63
64 if ( addr[0] == 0x10) {65
66 Serial.print("Device is a DS18S20 family device.\n");67
68 }69
70 else if ( addr[0] == 0x28) {71
72 Serial.print("Device is a DS18B20 family device.\n");73
74 }75
76 else {77
78 Serial.print("Device family is not recognized: 0x");79
80 Serial.println(addr[0],HEX);81
82 return;83
84 }85
86
87 ds.reset();88
89 ds.select(addr);90
91 ds.write(0x44,1); // start conversion, with parasite power on at the end92
93
94 delay(1000); // maybe 750ms is enough, maybe not95
96 // we might do a ds.depower() here, but the reset will take care of it.97
98
99 present = ds.reset();100
101 ds.select(addr); 102
103 ds.write(0xBE); // Read Scratchpad104
105
106 Serial.print("P=");107
108 Serial.print(present,HEX);109
110 Serial.print(" ");111
112 for ( i = 0; i < 9; i++) { // we need 9 bytes113
114 data[i] = ds.read();115
116 Serial.print(data[i], HEX);117
118 Serial.print(" ");119
120 }121
122 Serial.print(" CRC=");123
124 Serial.print( OneWire::crc8( data, 8), HEX);125
126 Serial.println();127
128}
Converting HEX to something meaningful (Temperature)
In order to convert the HEX code to a temperature value, first you need to identify if you are using a DS18S20, or DS18B20 series sensor. The code to read the temperature needs to be slightly different for the DS18B20 (and DS1822), because it returns a 12-bit temperature value (0.0625 deg precision), while the DS18S20 and DS1820 return 9-bit values (0.5 deg precision).
First, you need to define some variables, (put right under loop() above)
1int HighByte, LowByte, TReading, SignBit, Tc_100, Whole, Fract;
Then for a DS18B20 series you will need to add the following code below the Serial.println();
1LowByte = data[0];2
3 HighByte = data[1];4
5 TReading = (HighByte << 8) + LowByte;6
7 SignBit = TReading & 0x8000; // test most sig bit8
9 if (SignBit) // negative10
11 {12
13 TReading = (TReading ^ 0xffff) + 1; // 2's comp14
15 }16
17 Tc_100 = (6 * TReading) + TReading / 4; // multiply by (100 * 0.0625) or 6.2518
19
20 Whole = Tc_100 / 100; // separate off the whole and fractional portions21
22 Fract = Tc_100 % 100;23
24
25 if (SignBit) // If its negative26
27 {28
29 Serial.print("-");30
31 }32
33 Serial.print(Whole);34
35 Serial.print(".");36
37 if (Fract < 10)38
39 {40
41 Serial.print("0");42
43 }44
45 Serial.print(Fract);46
47
48 Serial.print("\n");
This block of code converts the temperature to deg C and prints it to the Serial output.
A Code Snippet for the DS 1820 with 0.5 Degree Resolution
The example shown above works only for the B-type of the DS1820. Below is a code example that works with the lower resolution DS1820 and with multiple sensors displaying their values on a LCD. The example is working with Arduino pin 9. Feel free to change that to an appropriate pin for your use. Pin 1 and 3 of the DS1820 have to be connected to ground! In the example a 5k resistor is connected from pin 2 of DS1820 to Vcc (+5V). See LiquidCrystal documentation for connecting the LCD to the Arduino.
1#include <OneWire.h>2
3#include <LiquidCrystal.h>4
5// LCD=======================================================6
7//initialize the library with the numbers of the interface pins8
9LiquidCrystal lcd(12, 11, 5, 4, 3, 2);10
11#define LCD_WIDTH 2012
13#define LCD_HEIGHT 214
15
16/* DS18S20 Temperature chip i/o */17
18
19OneWire ds(9); // on pin 920
21#define MAX_DS1820_SENSORS 222
23byte addr[MAX_DS1820_SENSORS][8];24
25void setup(void)26
27{28
29 lcd.begin(LCD_WIDTH, LCD_HEIGHT,1);30
31 lcd.setCursor(0,0);32
33 lcd.print("DS1820 Test");34
35 if (!ds.search(addr[0]))36
37 {38
39 lcd.setCursor(0,0);40
41 lcd.print("No more addresses.");42
43 ds.reset_search();44
45 delay(250);46
47 return;48
49 }50
51 if ( !ds.search(addr[1]))52
53 {54
55 lcd.setCursor(0,0);56
57 lcd.print("No more addresses.");58
59 ds.reset_search();60
61 delay(250);62
63 return;64
65 }66
67}68
69int HighByte, LowByte, TReading, SignBit, Tc_100, Whole, Fract;70
71char buf[20];72
73
74void loop(void)75
76{77
78 byte i, sensor;79
80 byte present = 0;81
82 byte data[12];83
84
85 for (sensor=0;sensor<MAX_DS1820_SENSORS;sensor++)86
87 {88
89 if ( OneWire::crc8( addr[sensor], 7) != addr[sensor][7])90
91 {92
93 lcd.setCursor(0,0);94
95 lcd.print("CRC is not valid");96
97 return;98
99 }100
101
102 if ( addr[sensor][0] != 0x10)103
104 {105
106 lcd.setCursor(0,0);107
108 lcd.print("Device is not a DS18S20 family device.");109
110 return;111
112 }113
114
115 ds.reset();116
117 ds.select(addr[sensor]);118
119 ds.write(0x44,1); // start conversion, with parasite power on at the end120
121
122 delay(1000); // maybe 750ms is enough, maybe not123
124 // we might do a ds.depower() here, but the reset will take care of it.125
126
127 present = ds.reset();128
129 ds.select(addr[sensor]); 130
131 ds.write(0xBE); // Read Scratchpad132
133
134 for ( i = 0; i < 9; i++)135
136 { // we need 9 bytes137
138 data[i] = ds.read();139
140 }141
142
143 LowByte = data[0];144
145 HighByte = data[1];146
147 TReading = (HighByte << 8) + LowByte;148
149 SignBit = TReading & 0x8000; // test most sig bit150
151 if (SignBit) // negative152
153 {154
155 TReading = (TReading ^ 0xffff) + 1; // 2's comp156
157 }158
159 Tc_100 = (TReading*100/2); 160
161
162 Whole = Tc_100 / 100; // separate off the whole and fractional portions163
164 Fract = Tc_100 % 100;165
166
167 sprintf(buf, "%d:%c%d.%d\337C ",sensor,SignBit ? '-' : '+', Whole, Fract < 10 ? 0 : Fract);168
169
170 lcd.setCursor(0,sensor%LCD_HEIGHT);171
172 lcd.print(buf);173
174 }175
176}
Suggest changes
The content on docs.arduino.cc is facilitated through a public GitHub repository. If you see anything wrong, you can edit this page here.
License
The Arduino documentation is licensed under the Creative Commons Attribution-Share Alike 4.0 license.